Biegler GmbH BW 685 Blood and Infusion Warmer

Disposable product for single use only. Sterile and pyrogen-free flow tube. For use with Biegler blood and infusion warmer. Luer-Lock, bubble trap and injection port.

The LifeWarmer Quantum Thermal Transfusion Set- Blood is the revolutionary IV tubing set that allows for safe, rapid warming of blood, blood products, or IV fluids without adding hardly any additional steps to the normal IV setup process. Modeled after standard blood infusion tubing, the familiar configuration allows for ease of use. The sophisticated intelligence and proprietary warming technology are integrated into the tubing system for simplicity and to reduce additional equipment and procedural steps. Roughly the same size and weight as standard blood tubing, there is almost no additional equipment burden.The Quantum IV administration tubing is double-extruded to yield a configuration that has both an inner tubing layer and an outer tubing layer. A conductive heating element is between the two layers but does not come in contact with the fluid path or disrupt the laminar flow. The outer tubing layer acts as an insulator while the inner tubing layer transfers the heat from the heating element to the fluid path. Thermistors (thermal resistors) located in the tubing continually measure temperature and provide that input to the Quantum Controller. The monitoring and independent application of energy (heat) along the fluid path allows the Quantum to respond to varying temperature inputs from the fluid source to near the point of patient entry to ensure fluid temperature is the right temperature at delivery.The Quantum Life Warmer, fully charged, is able to warm and maintain up to 2 units ( 900mL +/- 100mL) of cold (4C) blood products or IV solutions to a pre-set temperature of 100.4F (38+/- 2C) at a flow rate of 100 mL/min (depending on the ambient temperature). Or, approximately 1700 mL of 20C IV solution to a set point of 38C +/- 2C at a flow rate of 200 mL/min. Effective warming flow rates range from 2 to 200 mL/minute depending on input fluid temperature and ambient conditions.

The Lifewarmer Quantum Blood and Fluid Warming System is a Game-Changing innovation that has succeeded in closing a critical capability gap previously left exposed by other commercial off-the-shelf fluid warmers currently fielded. Size, weight, performance, and ease of use are no longer collective barriers to the delivery of whole blood in far forward and near point of injury (POI) prehospital casualty management.The Quantum exceeds all healthcare and logistical requirements for the delivery of warmed blood or fluids across the defined spectrum of care. The system consists of unique thermal administration sets that incorporate sensing elements with an integrated heating system that does not disrupt the fluid path. With advanced intelligence throughout the system, the lightweight Controller modulates and moderates the energy flow to the integrated heating elements to ensure consistent normothermic fluid delivery to the casualty. The 44V battery is the smallest in category, able to rapidly adjust power distribution based on the temperature and flow rate of the input fluid. This creates a highly efficient system capable of previously unrealized performance optimizations. The Quantum system has an operational weight of just 22 total ounces yet can deliver two units of 39°F Whole Blood (WB) at 100mL/min with an output temperature of 100.4°F (38°+/- 2°C) with only a 24 second warm-up period. The Quantum Blood and Fluid Warming System provides the Tactical Health Care Professional with significant technological overmatch in the fight to eliminate preventable combat death.Quantum System Contents:1 x Controller1 x Battery1 x Battery Charger2 x TTS-B (Thermal Transfusion Set - Blood)NOTE: TTS-B is Single Use Only, Supplied sterile via Ethylene Oxide

QinFlow Warrior Lite Blood and Fluid Warmer Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a LED panel display for user notifications.

QinFlow Blood and Fluid Warmer QiF-01 Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.

QinFlow Warrior Extreme Blood and Fluid Warmer Base Unit (BU). The BU controls the performance of the system and the outflow fluid temperature. The BU contains firmware (SW) and electronics (HW), a graphic display and audio speaker for user notifications.