The Angled Ceiling Plate (ACP) is a high quality, commercial grade installation accessory to be used with the SuperPole. The ACP is intended to permit the SuperPole to be installed in areas where the ceiling is vaulted or angled. The ACP attaches to the top of the pole and is adjustable in angle from 0-45°. The ACP must be secured to ceiling joists with appropriate fasteners. The ACP is only to be used with HealthCraft’s SuperPole System. The ACP is not to be used with the SuperPole Bariatric, SuperPole Ultra and Ceiling Plate Extender. The ACP is not to be used in any other way than described above.

The Angled Ceiling Plate (ACP) is a high quality, commercial grade installation accessory to be used with the SuperPole. The ACP is intended to angled. The ACP attaches to the top of the pole and is adjustable in angle from 0-45°. The ACP must be secured to ceiling joists with appropriate fasteners. The ACP is only to be used with HealthCraft’s SuperPole System. The ACP is not to be used with the SuperPole Bariatric, SuperPole Ultra and Ceiling Plate Extender. The ACP is not to be used in any other way than described above.

The SuperPole F.R.S. is a high quality, commercial grade support pole that interfaces with and is supported by a receptacle that is permanently embedded into a structural concrete floor. The SuperPole F.R.S. is intended for moderate vertical load bearing to provide sitting and standing support for people with reduced mobility. When the pole is removed, the receptacle must be covered with a floor flush cap to provide a water-tight seal. The maximum user weight for this product is 450lbs / 205kgs. Product is not intended to support full body weight.

The e2 Ceiling Mount Trapeze is an over-bed trapeze system that secures to the ceiling. The trapeze handle features two offset ladder rungs to allow for improved use of arm strength and increased comfort. Additionally, it can slide sideward / laterally on the ceiling mounted grab bar to store out of the way when not in use. The e2 Ceiling Mount Trapeze is intended for moderate vertical load bearing to provide sitting and standing support for people with reduced mobility. The grab bar is installed to a structural ceiling, and a metal hook is looped onto the grab bar. The trapeze handle is connected with an adjustable strap to the metal hook. The maximum user weight for this product is 300lbs / 136kgs. No more than 150lbs / 68kgs is to be exerted on the e2 trapeze (sitting support only). NOTE: Product is not intended to support full body weight.

The e2 Ceiling Mount Trapeze is an over-bed trapeze system that secures to the ceiling. The trapeze handle features two offset ladder rungs to allow for improved use of arm strength and increased comfort. Additionally, it can slide sideward / laterally on the ceiling mounted grab bar to store out of the way when not in use. The e2 Ceiling Mount Trapeze is intended for moderate vertical load bearing to provide sitting and standing support for people with reduced mobility. The grab bar is installed to a structural ceiling, and a metal hook is looped onto the grab bar. The trapeze handle is connected with an adjustable strap to the metal hook. The maximum user weight for this product is 300lbs / 136kgs. No more than 150lbs / 68kgs is to be exerted on the e2 trapeze (sitting support only). NOTE: Product is not intended to support full body weight.

The Angled Ceiling Plate is a high quality, commercial grade installation accessory to be used with the SuperPole.The Angled Ceiling Plate is intended to permit the SuperPole to be installed in areas where the ceiling is vaulted or angled.The Angled Ceiling Plate attaches to the top of the pole and is adjustable in angle from 0-45°. The Angled Ceiling Plate must be secured to ceiling joists with appropriate fasteners.The Angled Ceiling Plate is only to be used with HealthCraft’s SuperPole System.Floor To Ceiling Height = 93-99" / 2362-2515mm Max User Weight = 300lbs / 136kgs

The SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole (floor to ceiling safety pole). The horizontal bar can be lifted, pivoted and lowered to the next locking position around the SuperPole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves (every 45 degrees) to provide a mechanism strong enough for the SuperBar to support the user. It is important to set proper height and orientation of the SuperBar to optimize the user’s range of motion. The SuperBar is made from robust materials and is capable of supporting vigorous forces during proper / normal usage. The structural components of the pole are made from metal. The plastic bushings of the SuperBar allow the horizontal bar to be rotated without marking or damaging the pole.

The SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole (floor to ceiling safety pole). The horizontal bar can be lifted, pivoted and lowered to the next locking position around the SuperPole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves (every 45 degrees) to provide a mechanism strong enough for the SuperBar to support the user. It is important to set proper height and orientation of the SuperBar to optimize the user’s range of motion. The top plate and base plate can be easily separated from the SuperPole by use of multiple use fasteners (clevis and cotter pin). The top plate can be secured to the structural ceiling joist with wood screws: - if regular inspection (and if necessary, tightening) cannot be done - if pole is subjected to aggressive usage

The SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole (floor to ceiling safety pole). The horizontal bar can be lifted, pivoted and lowered to the next locking position around the SuperPole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves (every 45 degrees) to provide a mechanism strong enough for the SuperBar to support the user. It is important to set proper height and orientation of the SuperBar to optimize the user’s range of motion. Floor To Ceiling Height 93-99" / 2362-2515mm Max User Weight 450lbs / 205kgs

The SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole (floor to ceiling safety pole). The horizontal bar can be lifted, pivoted and lowered to the next locking position around the SuperPole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves (every 45 degrees) to provide a mechanism strong enough for the SuperBar to support the user. It is important to set proper height and orientation of the SuperBar to optimize the user’s range of motion. Floor To Ceiling Height 93-99" / 2362-2515mm Max User Weight450lbs / 205kgs

The SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole (floor to ceiling safety pole). The horizontal bar can be lifted, pivoted and lowered to the next locking position around the SuperPole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves (every 45 degrees) to provide a mechanism strong enough for the SuperBar to support the user. It is important to set proper height and orientation of the SuperBar to optimize the user’s range of motion. The floor to ceiling range and maximum user weight dependent on model. Note: Product is not intended to support full body weight. The SuperBar is only to be used with HealthCraft’s SuperPole System. The SuperBar is not to be used with the SuperPole Ultra. The SuperBar is not to be used in any other way than described above. Floor To Ceiling Height 93-99" / 2362-2515mm Max User Weight300lbs / 136kgs The SuperBar is made from robust materials and is capable of supporting vigorous forces during proper / normal usage. The structural components of the pole are made from metal. The plastic bushings of the SuperBar allow the horizontal bar to be rotated without marking or damaging the pole. The top plate and base plate can be easily separated from the pole by use of multiple use fasteners (clevis and cotter pin).The non-latex grip provides both comfort and traction for the hand. The top plate can be secured to the structural ceiling joist with wood screws:- if regular inspection (and if necessary, tightening) cannot be done- if pole is subjected to aggressive usage

The SuperPole is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperPole is installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. The floor to ceiling range and maximum user weight dependent on model. The SuperPole is made from robust materials and is capable of supporting vigorous forces during proper / normal usage. The structural components of the pole are made from metal. The components of the pole that make direct contact with the floor and ceiling are made of non-slip rubber to protect the surfaces from damage, as well as provide traction. The top plate and base plate can be easily separated from the pole by use of multiple use fasteners (clevis and cotter pin).The top plate can be secured to the structural ceiling joist with wood screws: - if regular inspection (and if necessary, tightening) cannot be done - if pole is subjected to aggressive usage

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperPole is installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. The floor to ceiling range and maximum user weight dependent on model. Note: Product is not intended to support full body weight.The SuperPole is not to be used in any other way than described above. The SuperPole is made from robust materials and is capable of supporting vigorous forces during proper / normal usage. The structural components of the pole are made from metal. The components of the pole that make direct contact with the floor and ceiling are made of non-slip rubber to protect the surfaces from damage, as well as provide traction. The top plate and base plate can be easily separated from the pole by use of multiple use fasteners (clevis and cotter pin). The top plate can be secured to the structural ceiling joist with wood screws: - if regular inspection (and if necessary, tightening) cannot be done - if pole is subjected to aggressive usage - if using SuperPole Heavy Duty (SP-HD)

The SuperPole Ultra is a high quality, commercial grade floor to ceiling safety pole (intended usage same as SuperPole). The SuperPole Ultra is intended for applications with floor to ceiling ranges from 121-140" / 3073-3556mm. The SuperPole Ultra is not to be used with the SuperBar, SuperTrapeze, Angled Ceiling Plate or Uni-Fit Extender. The SuperPole Ultra parts (pole, extension tube and top plate - labelled for convenience) should not be used with the components of any other floor to ceiling poles.

The Ceiling Plate Extender (CPE) is a high quality, commercial grade installation accessory to be used with the SuperPole. The CPE is intended to increase the top plate span of the SuperPole from 20-30" / 508-762mm. It can be used when the SuperPole is expected to be subjected to more aggressive use, or where structural ceiling joists have increase spacing (such as 24"/610mm between centers). The CPE is only to be used with HealthCraft’s SuperPole System. The CPE is not to be used with the Angled Ceiling Plate.

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water.

Custom cut to length.The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water.

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water. Floor To Ceiling Height 93-99" / 2362-2515mm Max User Weight 450lbs / 205kgs

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water Max user weight 450lbs / 205kg. floor to ceiling range 93-99" / 2362-2515mm

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water. Max Ceiling height 121-140" / 3073-3556mm Max User Weight 300lbs / 136kg

The SuperPole is a high quality, commercial grade floor to ceiling safety pole. The SuperPole must be installed between a structural floor and ceiling by turning a jackscrew at the bottom of the pole. The pressure created by the jackscrew is strong enough for the SuperPole to support the user, yet it does not require drilling holes into the floor or ceiling. This is ideal for relocating or removing the pole. NOTE: The top plate has two holes that may be used to fix the plate directly to the ceiling joist if necessary. Do not install the pole where it is directly exposed to water. Max user Weight 300lbs / 136kg ceiling height range 03-99" / 2362-2515mm

The Uni-Fit Extender is a high quality, commercial grade installation accessory to be used with the SuperPole. The Uni-Fit Extender is intended to increase the floor to ceiling range of the SuperPole from 93-99" to 100-120" (236-251cm to 254-305cm). The Uni-Fit Extender is a metal tube that attaches between the top plate and the pole assembly of the SuperPole. The Uni-Fit Extender features a series of holes that can be selected depending on the desired floor to ceiling height range. The Uni-Fit Extender is only to be used with HealthCraft’s SuperPole System. The Uni-Fit Extender is not to be used with the SuperTrapeze, SuperPole Bariatric or SuperPole Ultra. The Uni-Fit Extender is not to be used in any other way than described.

The SuperTrapeze is a high quality, commercial grade over-bed trapeze that connects to the SuperPole (floor to ceiling safety pole). The SuperTrapeze handle features two offset ladder rungs to allow for improved use of arm strength and increased comfort. Additionally, it can hook around the pole to store out of the way when not in use. The support arm has an adjustable strap that attaches to the trapeze handle. It is important to set proper height and orientation of the SuperTrapeze to optimize the user’s range of motion.

The SuperTrapeze is a high quality, commercial grade over-bed trapeze that connects to the SuperPole (floor to ceiling safety pole). The SuperTrapeze handle features two offset ladder rungs to allow for improved use of arm strength and increased comfort. Additionally, it can hook around the pole to store out of the way when not in use. The support arm has an adjustable strap that attaches to the trapeze handle. It is important to set proper height and orientation of the SuperTrapeze to optimize the user’s range of motion.

The SuperTrapeze is a high quality, commercial grade over-bed trapeze that connects to the SuperPole (floor to ceiling safety pole). The SuperTrapeze handle features two offset ladder rungs to allow for improved use of arm strength and increased comfort. Additionally, it can hook around the pole to store out of the way when not in use.The SuperTrapeze handle is intended for moderate vertical load bearing to provide sitting and standing support for people with reduced mobility. The SuperTrapeze handle is installed onto the SuperPole by securing a support arm to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the support arm in place, and the spring ring is used to prevent the set screws from back-threading. The support arm has an adjustable strap that attaches to the trapeze handle. The SuperTrapeze handle is strong enough to support the user when sitting up in bed and standing. It is important to set proper height and orientation of the SuperTrapeze to optimize the user’s range of motion. The maximum user weight for this product is 300lbs / 136kgs. Note: Product is not intended to support full body weight.

The SuperPole F.R.S. (floor receptacle system) with SuperBar is a high quality, commercial grade pivoting and locking horizontal bar that connects to the SuperPole F.R.S. (a support pole that interfaces with and is supported by a receptacle that is permanently embedded into a structural concrete floor). The horizontal bar can be lifted, pivoted, and lowered to the next locking position around the F.R.S. pole. The SuperBar is intended for moderate vertical and horizontal load bearing to provide sitting and standing support for people with reduced mobility. The SuperBar is installed onto the SuperPole F.R.S. by securing a castellated collar to the pole with 3 cone point set screws. The set screws pierce into the pole and lock the collar in place, and the spring ring is used to prevent the set screws from back-threading. The castellated collar has 8 grooves strong enough for the SuperBar to support the user. When the SuperPole F.R.S. is removed from the concrete receptacle, the receptacle must be covered with a floor flush cap to provide a water-tight seal. The maximum user weight for this product is 450lbs / 205kgs. Product is not intended to support full body weight.

LOAD LOKS, LARGE,4/SET

(XXL) SOFT STRETCHER 60"x80"ea

LOAD LOKS, XXL,4/SET

THE MORR MOVER

THE MORR MOVER-5 EACH

BACKBOARD PAD, EACH

THE "QT" QUICK TRANSPORT

THE "QT" QUICK TRANSPORT CS 10

LOAD GRIPS SET/4

LOAD GRIPS SET/4

MORRISON SELECT BACKBOARD

MORRISON SELECT BACKBOARD

MORRISON SELECT BACKBOARD

MORRISON MCI BACKBOARD

MORRISON MCI BACKBOARD

STRETCHER NET

NET 35-1

NET 35-2 W/ANGLES

HEAD IN POUCH

BASE STORAGE NET - STRYKER

BASE STORAGE NET -UPGRADE

FLAT HEADED POUCH

GROMMETED BLACK FLAT MAT

BUCKLE WRAP