BE 105-8 Bronchoscope Swivel - 15mm ID/22mm OD (patient port) x15mm OD (equipment port). Reusable. Fits components of adult ventilator circuits. Molded of polyetherimide. Includes two silicone rubber caps; one cap allows for the use of a suctioning catheter while the other cap allows for the use of a fiber-optic bronchoscope without significant loss of PEEP.

Specialty Adapter with Vent - 15mm ID/22mm OD/15mm ID/22mm OD. Fits components of adult ventilator circuits. Molded of polycarbonate. Reusable.

The BE 114-1 Flexible Support Arm Pole Bracket permits mounting of "Flexible Support Arms" to poles up to 1" in diameter. Components and materials: bracket body: anodized aluminum; screw: steel with phenolic handle. Made in the USA.

The BE 114-2 Flexible Support Arm Pole Bracket permits mounting of "Flexible Support Arms" to poles up to 1.5" in diameter. Components and materials: bracket body: anodized aluminum; screw: steel with phenolic handle. Made in the USA.

The BE 114-5 Flexible Support Arm Universal Rail Mount Bracket permits rail mounting of "Flexible Support Arms". The BE 114-5 is not compatible with rails mounted flush to wall. Components and materials: bracket body: anodized aluminum; screw: steel with phenolic knob. Made in the USA.

The BE114-5TB Flexible Support Arm Single Tubing Clamp holds a ventilator tube in place when attached to an III "Flexible Support Arm". Made of polypropylene with phenolic ball knob mount. Made in the USA.

The reusable BE 117 Non-Rebreathing ‘T’ is designed for use with a spontaneously breathing patient where “back flow” must be avoided. The ‘T’ is designed to prevent the flow of gas back toward the source and to ensure unilateral breathing.

The BE 117-W Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Can be used to easily add a monitoring device such as a temperature probe to the breathing circuit. Dimensions: 22mm O.D. x 22mm I.D. x 15mm I.D./22mm O.D. Single Patient Use. Molded of High Density Polyethylene.

Specialty Mouthpiece Adapter with 22mm ID fitting. Molded of polystyrene butadiene. Single Patient Use.

Specialty Adapter - 22mm ID x 22mm OD Adapter for ventilator circuits/CPAP systems. Molded of polystyrene butadiene. Single Patient Use.

BE 122-24 Flexible Support Arm - 24" - (With extension, reaches 38" total length) - Use to support ventilator tubing; Rotates up to 360° and can be locked in place. Adapts to most ventilators by using Flexible Support Arm Brackets. Ventilator tubing is held in place with Flexible Support Arm Tubing Clamps mounted to the Flexible Support Arm. All are manufactured in the USA by Instrumentation Industries, Inc.

BE 122-2TB - 8" Flexible Support Arm Double Tubing Clamp holds two ventilator tubes in place when attached to an III "Flexible Support Arm". Made of polypropylene and anodized aluminum with phenolic ball knob. Made in the USA.

BE 122-2TSB - 4" Flexible Support Arm Double Tubing Clamp holds two ventilator tubes in place when attached to an III "Flexible Support Arm". Made of polypropylene and anodized aluminum with phenolic ball knob. Made in the USA.

BE 122-30 Flexible Support Arm - 30" - (With extension, reaches 44" total length) - Use to support ventilator tubing; Rotates up to 360° and can be locked in place. Adapts to most ventilators by using Flexible Support Arm Brackets. Ventilator tubing is held in place with Flexible Support Arm Tubing Clamps mounted to the Flexible Support Arm. All are manufactured in the USA by Instrumentation Industries, Inc.

The BE 125 Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Dimensions: 22mm O.D. x 15mm I.D./22mm O.D. x 15mm O.D./22mm O.D Reusable.

The BE 125-1 Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Dimensions: 22mm O.D. x 22mm O.D. x 15mm I.D./22mm O.D Reusable.

The BE 125-1T Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Dimensions: 22mm O.D. x 22mm I.D. x 15mm I.D./22mm O.D Reusable.

The BE 125-1TD Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Can be used to easily add a monitoring device such as a temperature probe to the breathing circuit. Dimensions: 22mm O.D. x 22mm I.D. x 15mm I.D. Single Patient Use. Molded of High Density Polyethylene.

BE 127 Wye Connector with (2) 22mm OD ports and (1) 15mm ID/22mm OD port. Fits components of adult ventilator circuits. Reusable.

BE 127-40 Wye Connector with (2) 22mm OD ports, (1) 15mm ID/22mm OD port and (1) barbed pressure port. Fits components of adult ventilator circuits. Reusable.

BE 127-7.5 Wye Connector with (2) 22mm OD ports, (1) 15mm ID/22mm OD port and 7.5mm temperature probe port. Fits components of adult ventilator circuits. Reusable.

BE 127-7.5-40 Wye Connector with (2) 22mm OD ports, (1) 15mm ID/22mm OD port, (1) 7.5mm ID temperature probe port, and (1) barbed pressure port. Fits components of adult ventilator circuits. Reusable.

The reusable BE 130 One-Way Valve is designed for use in any breathing circuit or ventilatory system where "back flow" must be avoided. It is designed to prevent the flow of gas back toward the source.

The reusable BE 130-22B One-Way Valve is designed for use in any breathing circuit or ventilatory system where "back flow" must be avoided. It is designed to prevent the flow of gas back toward the source.

The reusable BE 130-23BB One-Way Valve is designed for use in any breathing circuit or ventilatory system where "back flow" must be avoided. It is designed to prevent the flow of gas back toward the source.

The reusable BE 131 One-Way Valve is designed for use in any breathing circuit or ventilatory system where "back flow" must be avoided. It is designed to prevent the flow of gas back toward the source.The device includes a silicone rubber connector with 22mm I.D. Inlet.

The BE 139 Pressure Adapter: Dimensions - Barbed port fits 3/16" I.D. tubing x 15mm I.D./22mm O.D. x 15mm O/D.

Reducing Adapter for use in breathing/ventilator circuit. - 15mm O.D. x 15mm I.D./22mm O.D. Molded of polycarbonate. Reusable.

The reusable BE 142 is designed for use with ventilators, anesthesia machines, resuscitators, and other systems where PEEP or CPAP is required. A threshold-like resistance is applied after active exhalation. The PEEP valve prevents the exhalation pressure from dropping below a pre-determined value. PEEP ranges are adjustable from 3 to 20cm of water. Maximum PEEP can vary +/-10%. Objectives of PEEP therapy: 1) increase functional residual capacity by maintaining a positive pressure throughout the ventilatory cycle - improves gas distribution,2) aid in the prevention of atelectasis via aveolar stinting, 3) decrease in the inspired oxygen fraction (FiO2) is an advantage, 4) help in the stabilization of flail chest condition, and 5) monitor tidal volume by connecting a spirometer to the outlet port.

The reusable BE 142-A is designed for use with ventilators, anesthesia machines, resuscitators, and other systems where PEEP or CPAP is required. A threshold-like resistance is applied after active exhalation. The PEEP valve prevents the exhalation pressure from dropping below a pre-determined value. PEEP ranges are adjustable from 3 to 20cm of water. Maximum PEEP can vary +/-10%. Objectives of PEEP therapy: 1) increase functional residual capacity by maintaining a positive pressure throughout the ventilatory cycle - improves gas distribution,2) aid in the prevention of atelectasis via aveolar stinting, 3) decrease in the inspired oxygen fraction (FiO2) is an advantage, 4) help in the stabilization of flail chest condition, and 5) monitor tidal volume by connecting a spirometer to the outlet port.

The BE 145-1522P Hose Connector: Dimensions - 15mm I.D/22mm O.D. x tapered barb adapter

The BE 145-2230P Hose Connector: Dimensions - 22mm I.D/30mm O.D. x tapered barb adapter

The BE 145-2P Hose Connector: Dimensions - 15mm O.D. x tapered barb adapter

The Instrumentation Industries, Inc. BE 148-1 Gauge Adapter changes 1/4" NPT connection to 1/8" small bore tubing connection.The BE 148-1 is designed to work with III Vacuum/Pressure Gauges and NIF Meters.The adapter is made of polycarbonate.

The BE 148-4 Cuff Pressure Monitor Adapter attaches to NS Series gauges with a 1/4" NPT fitting to create a Cuff Pressure Monitor. During ventilation, the NS Series Cuff Pressure Monitors are devices used to periodically monitor endotracheal or tracheostomy tube balloon pressure to assure an adequate seal between the tube and the tracheal wall.These devices are intended to be used by or on the order of a physician.

The BE 148-5-1 Gauge Clamp is an accessory to the NS Series Vacuum/Pressure Gauges. The BE 148-5-1 securely mounts Gauges with a rear 1/4" NPT thread to 3/4" diameter poles.

The BE 148-5-2 Gauge Clamp is an accessory to the NS Series Vacuum/Pressure Gauges. The BE 148-5-2 securely mounts Gauges with a rear 1/4" NPT thread to poles with 3/4" to 1-1/2" diameter.

The BE 148-5-2.5 Gauge Clamp is an accessory to the NS Series Vacuum/Pressure Gauges. The BE 148-5-2.5 is used to securely mount Gauges with a rear 1/4" NPT thread to medical equipment such as poles, incubators, ventilators, etc. The BE 148-5-2.5 clamp works with equipment that requires a clamp having a 1" to 2-1/2" opening.

The BE 148-5-3.5 Gauge Clamp is an accessory to the NS Series Vacuum/Pressure Gauges. The BE 148-5-3.5 is used to securely mount Gauges with a rear 1/4" NPT thread to medical equipment such as poles, incubators, ventilators, etc. The BE 148-5-3.5 gauge clamp works with equipment that requires a clamp having a 2-1/2" to 3-1/2" opening.

The Instrumentation Industries, Inc. BE 148-6 Gauge Adapter has a 1/8" tubing connection on one end and a 15 mm I.D./22 mm O.D. connection on the other end for remote inspiratory monitoring.The BE 148-1 is designed to work with III Vacuum/Pressure Gauges and NIF Meters.The adapter is made of polycarbonate.

The Instrumentation Industries, Inc. BE 149-1 Gauge Adapter has a 1/4" NPT connection on one end and a 15 mm I.D./22 mm O.D. connection on the other end for inspiratory monitoring.The BE 149-1 is designed to work with III Vacuum/Pressure Gauges and NIF Meters.The adapter is made of polycarbonate.

BE 150-5G Test Lung has a 22mm I.D. connection and a 1 liter capacity; Not made with natural rubber latex. Not for patient use.

BE 150-5LF Test Lung has a 22mm I.D. connection and a 750 ml capacity; Not made with natural rubber latex. Not for patient use.

The BE 16-2 Tee Adapter is intended for use in a ventilator, oxygen or BIPAP circuit. Dimensions: 22mm I.D. x 18mm I.D./22mm O.D. x 18mm I.D./22mm O.D Reusable.

BE 169 Oxygen Tank Wrench with 12" Security Cable. Wrench fits the valve stem of E-cylinder-type oxygen tanks and is manufactured of zinc-plated steel. The security cable is Nylon-coated stainless steel.

BE 169-W Oxygen Tank Wrench fits the valve stem of E-cylinder-type oxygen tanks. Manufactured of zinc-plated steel.

The BE 183-SU Manual Jet Ventilator is designed to provide trans-tracheal ventilation in specific emergency situations of upper airway obstructions. This system is used in conjunction with a trans-tracheal catheter, or cricothyrotomy needle, which is inserted through the cricothyroid membrane. Ventilation is accomplished by the manual, intermittent jetting of oxygen through the catheter for subsequent lung inflation.

The BE 183-SU-12 Manual Jet Ventilator is designed to provide trans-tracheal ventilation in specific emergency situations of upper airway obstructions. This system is used in conjunction with a trans-tracheal catheter, or cricothyrotomy needle, which is inserted through the cricothyroid membrane. Ventilation is accomplished by the manual, intermittent jetting of oxygen through the catheter for subsequent lung inflation.

The BE 183-SUR Manual Jet Ventilator is designed to provide trans-tracheal ventilation in specific emergency situations of upper airway obstructions. This system is used in conjunction with a trans-tracheal catheter, or cricothyrotomy needle, which is inserted through the cricothyroid membrane. Ventilation is accomplished by the manual, intermittent jetting of oxygen through the catheter for subsequent lung inflation.

The BE 183-SUR-12 Manual Jet Ventilator is designed to provide trans-tracheal ventilation in specific emergency situations of upper airway obstructions. This system is used in conjunction with a trans-tracheal catheter, or cricothyrotomy needle, which is inserted through the cricothyroid membrane. Ventilation is accomplished by the manual, intermittent jetting of oxygen through the catheter for subsequent lung inflation.